4.7from 936 verified reviewsFree Australia-Wide DeliveryQuick Dispatch

Sales & Support 1800 769 858 Service Account Retail

Cart

RedBack XLG44 laser level in use on a fit-out job

Fit-Out · 25 Years

Fit-Out Laser Levels – Walls, partitions, cabinets.

Multi-line lasers for fit-out work. Project a level horizontal, plumb verticals, and a 90° square – solo, in seconds. Premium 9-diode XLG44 family for daily commercial work; budget multi-line and cross-line for occasional jobs.

If you’re after a laser level for fit out work, this page covers the lot – cabinet installation, downlight set-out, partitions and ceiling grids – plus the mounts and receivers that go with them.

4.7936 reviews

Shop fit-out lasers Call 1800 769 858

Only need a laser now and then? Jump to the budget multi-line & cross-line range ↓

Level, Plumb & Square From One Set-UpClass 3 Green Beam OptionsUp to 5× Brighter than Class 29-Diode XLG44 for Maximum BrightnessPulse Mode for Outdoor Receiver UseIn-House Repairs & Calibration in Australia25 Years of Laser LevelsAustralian Phone Support 1800 769 858

Product Group One

Premium ultra-bright multi-line range

Class 3 green multiline laser levels built for daily commercial fit-out – calibratable, repairable, up to 5× brighter than Class 2. Led by the 9-diode XLG44 with servo-electronic levelling for +/-1mm @ 10m accuracy, alongside the 3D Green3DMAX and the plumb-axis CX610G. Perpendicular verticals plus a horizontal – level, plumb and square in a single set-up.

Out of Stock

NEW!

Line LaserNEW!

CX610G

Rated 5.00 out of 5 based on 1 customer rating

Accuracy +/- 2mm @ 10m

Brightness Class 3 (Green)

Plumb-Dot Multi-Line Laser

4x Verticals, 1x Horizontal

Auto-Levelling - Pendulum

80m Outdoor Range (Optional Receiver)

Out of Stock

NEW!

Line LaserNEW!

Green3DMAX

Rated 5.00 out of 5 based on 1 customer rating

Accuracy +/- 2mm @ 10m

Brightness Class 3 (Green)

3D Multi-Line Laser

2x 360° Verticals, 1x 360° Horizontal

Auto-Levelling - Pendulum

80m Outdoor Range (Optional Receiver)

Out of Stock

Australia's Best

Line LaserAustralia's Best

XLG44

Rated 5.00 out of 5 based on 1 customer rating

Accuracy +/- 1mm @ 10m

Brightness Class 3 (Green)

Plumb-Dot Multi-Line Laser

4x Verticals, 4x Horizontals

Auto-Levelling - Electronic

80m Outdoor Range (Optional Receiver)

Not sure which one? The comparison below breaks the three down spec by spec.

Product Group Two

Budget multi-line & cross-line range

Cost-effective lasers that handle most levelling, alignment, plumb and set-out work. Cross-line for simple level-and-plumb jobs; multi-line for full 360° fit-out work without the premium price.

53% Off

Line Laser

L203

Rated 4.79 out of 5 based on 19 customer ratings

Accuracy +/- 2mm @ 10m

Brightness Class 2 (Red)

Plumb-Dot Multi-Line Laser

2x Verticals, 1x Horizontal

Auto-Levelling - Pendulum

80m Outdoor Range (Optional Receiver)

40% Off

Line Laser

UN671D

Rated 4.71 out of 5 based on 24 customer ratings

Accuracy +/- 2mm @ 10m

Brightness Class 2 (Red)

Cross Line Laser

1x Vertical, 1x Horizontal

Auto-Levelling - Pendulum

33% Off

Line Laser

UNL59

Rated 4.28 out of 5 based on 18 customer ratings

Accuracy +/- 2mm @ 10m

Brightness Class 2 (Red)

Plumb-Dot Multi-Line Laser

4x Verticals, 1x Horizontal

Auto-Levelling - Pendulum

80m Outdoor Range (Optional Receiver)

Out of Stock

Line Laser

UNG6001

Rated 4.73 out of 5 based on 11 customer ratings

Accuracy +/- 2mm @ 10m

Brightness Class 3 (Green)

Cross Line Laser

1x Vertical, 1x Horizontal

Auto-Levelling - Pendulum

80m Outdoor Range (Optional Receiver)

40% Off

Line Laser

UNG6631B

Rated 4.50 out of 5 based on 8 customer ratings

Accuracy +/- 3mm @ 10m

Brightness Class 3 (Green)

3D Multi-Line Laser

2x 360° Verticals, 1x 360° Horizontal

Auto-Levelling - Pendulum

80m Outdoor Range (Optional Receiver)

27% Off

Line Laser

UNG641

Rated 4.50 out of 5 based on 4 customer ratings

Accuracy +/- 2mm @ 10m

Brightness Class 3 (Green)

Plumb-Dot Multi-Line Laser

4x Verticals, 1x Horizontal

Auto-Levelling - Pendulum

80m Outdoor Range (Optional Receiver)

Out of Stock

Line Laser

UNG6631

Rated 4.83 out of 5 based on 6 customer ratings

Accuracy +/- 3mm @ 10m

Brightness Class 3 (Green)

3D Multi-Line Laser

2x 360° Verticals, 1x 360° Horizontal

Auto-Levelling - Pendulum

80m Outdoor Range (Optional Receiver)

Want the complete line-up, including outdoor squaring kits? See the full line laser range.

Video Hub

Fit-out lasers on the job

Watch the range in action – the XLG44 electronic-levelling multi-line, the UNG6631 360° kit for flooring and interior fit-out, and a two-minute guide to which laser type your work needs.

Fit-out lasers playlist

View our channel

Use cases

Fit-out jobs a laser pays for itself on

Where a multi-line laser earns its keep on fit-out work – most of these are jobs you’d otherwise mark twice with a chalk line and a long spirit level.

01 · Partitions

Wall & partition set-out

Square laser projects two perpendicular vertical lines plus a horizontal – set out partition runs, internal walls and door openings off a single set-up. Perfect right angles without a string line.

02 · Cabinetry

Cabinetry & joinery installs

Carcass top line, bench height, overhead-cabinet datum – every height marked off the same laser line. Square laser sets the run for L-shaped or U-shaped cabinet work.

03 · Ceilings

Suspended ceiling grid

Level horizontal line all the way around the room sets the grid track height in one set-up. Read the line off the wall, fix the track, every wall hits the same level.

04 · Downlights

Downlight & HVAC grids

Square multi-line laser sets the row and column lines for any ceiling-mounted grid in one set-up. Mark the intersections, drill the cans or cut the diffusers, every fitting hits the right spot.

05 · Services

GPO, switch & data outlets

Set the laser at outlet height and walk every plate on the wall to the line. One person, no chalk line, every outlet hits the same level.

06 · Racking

Pallet racking & shelving

Plumb verticals on every upright, level horizontals across every beam line. Long warehouse-scale runs without re-measuring at every post.

On Video · Downlight Set-Out

Downlight installation with an indoor laser

A two-minute comparison of the indoor dot, 3D and multi-line lasers electricians use for downlight installation and electrical fit-out. The same grid method covers HVAC diffusers, sprinkler heads and any other ceiling-mounted layout.

Sparkies have their own page – laser levels for electricians – and tilers use the same square verticals to keep tile lines honest: see lasers for tiling. Transferring single points floor-to-ceiling instead? That’s a job for a dot laser.

Video

Red or Green?

Red beam or green beam?

In RedBack’s premium multi-line range, red and green beams have similar power outputs (<5 mW) – brightness is almost identical to the eye. Pick by working range and budget, not by visibility.

Red Beam

Cheaper, longer outdoor range

Cheaper than the green equivalent. Pairs with a line-laser receiver for outdoor work at a longer range – roughly 150 m radius vs the green’s 40 m. Pick red if you’ll use a receiver outdoors.

Best for:

Indoor fit-out where line is visible
Outdoor decking / pergola with receiver
Anyone wanting a cheaper premium laser

Green Beam

More visible to the eye in some lighting

Same diode power as the red, but the green wavelength reads brighter to the human eye in some conditions. Shorter range with a receiver. Pick green if it’s a pure indoor laser and you never use a receiver outdoors.

Best for:

Pure indoor fit-out work
Brightly lit indoor commercial sites
Premium feel, premium price

Buyer’s Guide

How to choose a fit-out laser level

Start with the job in front of you – cabinet installation, wall set-out, ceiling grids or floor levelling – then match the lines, brightness and accuracy to how often the laser earns its keep.

Kitchens, cabinets & joinery

Pick a laser that rotates around its plumb axis – the XLG44 for daily installs, or the UNG641 on a budget. Set the carcass line once, swing the verticals to square the run.

Partitions & wall set-out

Two perpendicular verticals plus a horizontal set out walls off one set-up. The Green3DMAX covers the full room with 3 × 360° lines; the CX610G runs 4 verticals at 90° to each other.

Ceiling grids, downlights & services

Full 360° coverage marks grid lines and heights in one set-up – the UNG6631 kit or the UNG6631B. Electrical work? See lasers for electricians.

Flooring & floor levelling

The UNG6631B and UNG6631 project a horizontal line that sits 8mm above the floor – easy tape-measure floor checks.

Occasional level & plumb jobs

A cross-line laser is enough – the L203 or UN671D in red, or the Class 3 green UNG6001 for brighter rooms.

Outdoor levelling, falls & set-out

Line lasers work outdoors with a receiver – red beam to roughly 150m radius with the LLR705. For big outdoor runs and drainage grades, step up to a rotating laser or grade laser.

RedBack premium fit-out laser comparison – levelling, lines, range and batteryCompare Premium Models

RedBack premium fit-out laser comparison: levelling, lines, range and battery
	XLG44	Green3DMAX	CX610G
Levelling	Servo-electronic self-levelling	Heavy-duty pendulum self-levelling	Ultra-fast pendulum auto-levelling
Accuracy	+/-1mm @ 10m	+/-2mm @ 10m	+/-2mm @ 10m
Laser lines	360° multi-line, 9 diodes (1 per line + plumb dot)	3 × 360° lines – 1 horizontal + 2 verticals at 90°	4 verticals at 90° + 1 horizontal (120° fan), red plumb dot below
Visible range	Up to 40m radius indoors	Up to 40m radius (light dependent)	Up to 30m radius (light dependent)
Range with receiver	Up to 50m radius, 100m diameter	40m radius, 80m diameter	40m radius, 80m diameter
Battery	Li-ion rechargeable or AA batteries	2 × Li-ion with USB-C charging	2 × Li-ion with Type-C charging
Best for	Daily commercial fit-out – maximum brightness & accuracy	Full-room 3D coverage – level, square & plumb in one	Squares & set-out around the plumb axis
	View →	View →	View →

Standard on every premium model: Class 3 <5mW green beam · IP54 dust & water resistance · pulse mode for optional outdoor receiver · 2 year warranty · calibratable and repairable in Australia.

Levelling slabs, setting falls or working long outdoor runs is a different tool – see rotating lasers and grade lasers.

Why RedBack

The RedBack difference

Anyone can sell a laser. Few back it properly.

01 · Specialists

Specialist range, not filler

We sell laser levels and measurement tools – that’s it. Every laser on this page is one we’ve used and chosen because it works for fit-out, not because it fills a catalogue page.

02 · Repairable

Built to last, built to be repaired

Solid construction, built for the long term. RedBack provides in-house repair and calibration services for all RedBack lasers and most other laser brands.

03 · Real People

Real support, real people

Call us and you’ll speak to someone who knows the products. No scripts, no call centre, no runaround – just straight answers from people who’ve worked with these tools for 25 years.

Pair With

Accessories for fit-out work

Indoor monopole for floor-to-ceiling height adjustment, wall mount bracket for permanent positions, suction-mount for adjustable in-room positions, plus line laser receivers for outdoor work.

Out of Stock

3MIMP Indoor Monopole interior fit out laser level

Tripods & Staffs 3MIMP - Indoor Monopole 1/4 inch & 5/8 Survey Thread $149.00inc GST View →

DC10 Suction laser Mount Continuos automatic electronic suction motor

Mounts DC10 - 3 in 1 Suction Laser Mount with Dust Collector and Green Laser $149.00inc GST View →

17% Off

Laser Receiver

LLR705

Rated 5.00 out of 5 based on 4 customer ratings

Sensor Length 55mm

Accuracy 1mm

Line Lasers

Red & Green Lasers

Diminishing Arrow Display

2 Accuracy Settings

Audible Speaker (Toggleable)

Out of Stock

Laser Receiver

LLR805MM

Sensor Length 100mm

Accuracy 1mm

Line Lasers

Red & Green Lasers

+/-25mm Display & Arrows

3 Accuracy Settings

Audible Speaker (Toggleable)

WB5 Wall Mount Bracket RedBack Lasers interior fit out suspended ceiling plastering installation

Mounts WB5 - Wall Mount Bracket 5/8 Survey Thread $119.00inc GST View →

FAQ

Fit-out laser questions

What laser level do I need for fit-out work?

A multi-line laser. It projects a level horizontal, plumb verticals and a 90° square – solo, in seconds – which covers most fit-out jobs: wall and partition set-out, cabinetry, ceiling grids and services layout. The premium 9-diode XLG44 family suits daily commercial work; budget multi-line and cross-line lasers handle occasional jobs.

What’s the best laser level for cabinet installation?

One with a horizontal line for heights plus vertical lines for the run. Carcass top line, bench height, overhead-cabinet datum – every height marked off the same laser line, and the square verticals set the run for L-shaped or U-shaped cabinet work. Lasers that rotate around their plumb axis – the XLG44 for daily installs or the UNG641 on a budget – make squaring cabinet runs easier.

Red beam or green beam – which is better for fit-out?

In RedBack’s premium multi-line range, red and green beams have similar power outputs (under 5mW) – brightness is almost identical to the eye, so pick by working range and budget, not by visibility. Red is cheaper and pairs with a line laser receiver outdoors at roughly 150m radius vs the green’s 40m. Green reads brighter to the human eye in some indoor conditions – the pick for a pure indoor laser.

Can I use a fit-out laser level outdoors?

Indoors the line is visible to the eye. Outdoors or in bright light the beam washes out, so run pulse mode with a line laser receiver like the LLR705 – it detects red line lasers to roughly 150m radius and green to 40m. For long-range outdoor levelling, falls and drainage, a rotating laser or grade laser is the better tool.

What’s the difference between a cross-line laser and a multi-line laser?

A cross-line laser projects one horizontal and one vertical line – enough for simple level-and-plumb jobs. A multi-line laser adds extra verticals, or full 360° lines, for square, alignment and complete room coverage – full fit-out work without moving the laser. The complete range is on our line lasers page.

How do I set out downlights with a laser level?

Use a square multi-line laser to set the row and column lines for the ceiling grid in one set-up. Mark the intersections, drill the cans or cut the diffusers – every fitting hits the right spot. The same method covers HVAC diffusers and any ceiling-mounted grid. Electricians: see the dedicated electrical fit-out laser page.

How accurate are fit-out laser levels?

The servo-electronic XLG44 is rated +/-1mm at 10m – the most accurate in this range. Pendulum-levelling models like the Green3DMAX and CX610G are rated +/-2mm at 10m, and the budget 3D models +/-3mm at 10m. All of them self-level automatically.

Do I need a tripod for a fit-out laser?

Not always. The 3MIMP indoor monopole locks a laser at any height in rooms up to 3m without a tripod, the WB5 wall bracket gives height-adjustable wall mounting, and the DC10 suction mount holds a laser on a wall without magnets or drilled holes. Most models also take a standard tripod thread.

Real support. Real people.

Speccing a fit-out laser kit?

25 years of laser-level experience on the other end of the phone. Tell us the work – domestic, commercial, industrial – and we’ll match you to the right multi-line laser.

Call 1800 769 858 Shop the range

4.7Australia’s Highest Rated Laser LevelsSee all 936 reviews →

CCRAIG GILL1 week agoVerified

excellent service and delivery time was fast aswell

AAnonymous1 week agoVerified

Great service and quick delivery

AAnonymous1 week agoVerified

Great product and quick delivery

GGerry Rohde2 weeks agoVerified

Awesome customer experience from the out of hours messaging to the speedy delivery 😀 👍

KKevin J.3 weeks agoVerified

A phone call to confirm that the 10 year old battery needed replacing made getting back to work easy

JJay Saunders4 months agoVerified

Redback lasers sent the product fast which saw me receive the product in no time. I also received a free upgrade to a lr730 which I was stoked about. The LR730 works a treat for getting heights set out precisely

KKaron Collier4 months agoVerified

As I purchased it for my cousin to use and it has made the job so much easier with alot more jobs to do so it will be getting a workout But very happy with the product

BBradley Barber5 months agoVerified

We just received our first rotating lasor level from RedBack and so far has been great Fast postage , easy ordering and arrived safe and works perfectly

BBearing Logistics6 months agoVerified

Great customer service and open dialogue and follow up. 100% deserved the five stars. Well done

FFranz Franz6 months agoVerified

Customer service was above and beyond. Product has met and beaten expectations. They were sold out of the package deal I wanted but contacted me directly when stock came in to offer it without waiting for it to go online. Had the laser over two weeks now and it's light beam is brighter than my mates DeWalt and the receiver works at a longer distance. Another cool feature is that the batteries have a USB C port on them for charging with USB C cable instead of needing another charger. Was dubious about them being cheaper than others on the market but I honestly can't fault it. Carry box also feels strong and sturdy.